BSF horizontal square angle grinder instructions for use
BSF horizontal type angle grinder is a newly developed angle grinder, it can also type the other four edges of one-time grinding disk, can be widely used for grinding angle square type magnetic steel, ceramic, crystal, quartz glass and other hard brittle materials.
Main parameters of machine tools:
1, processing parts thickness range: 2 ~ 30mm
2, processing parts width range: 12~100 mm (length / width less than 4)
3, processing length range: 15~100 mm
4, processing parts tolerance: < 0.05 mm
5, processing line speed: 160~220 cm/min
6, grinding allowance: 0.1 x 45 degrees to 0.4 x 45 degrees
7, grinding after cleanliness: 1.6
8, main motor: 0.75KW * 2800r/min; conveyor belt motor: 90YS60GV22; rubber guide wheel motor: 100YT200DV22; cooling pump: 40W, DB-12A
9, power: three-phase 50Hz 380V/220V
10, coolant: special grinding fluid
Three. Name of each part of machine tool:
1, rack parts.
The 2 and 4 grinding head parts are composed of a grinding head base, a grinding head box, a main shaft, a main shaft belt pulley, a diamond grinding wheel and a bearing, an electric motor, a motor belt pulley, a multi wedge belt, an electric motor, a moving bottom plate, etc..
The 3 and 2 carriage parts are composed of upper and lower carriage, screw rod, nut and so on.
4, the 2 pay mechanism composed of a pair of lifting gear, screw, nut, bearing, wheel etc..
5. The rail parts are composed of vertical guide rail, horizontal guide rail, guide rail soleplate, guide rail adjusting mechanism and so on.
6. The feed feeding part is composed of a set of conveyer belts and a pair of rubber guide wheels.
7. The cooling parts are composed of cooling pump, oil tank, distributing valve and water jet pipe.
8 、 power control system consists of 6 motors, control box, distribution box and so on.
Four. Operation procedure of machine tools:
1. Turn on the direction of the wheel before you turn on the machine to see if it is rotated in the correct direction as shown in the arrow.
2. Adjust the distance between the movable track and the fixed guide plate so that it can make the workpiece pass smoothly.
3, adjust the grinding wheel position, determine the best grinding angle and grinding amount.
4, adjust the distance between the rubber guide wheel, not only can make the workpiece pass smoothly, but also can produce a driving force to ensure that the workpiece complete the whole process.
5, in case of workpiece thickness changes, you need to adjust the two grinding head height, you must first loosen the two side fastening screws, and then turn the lifting handwheel, the two grinding head adjusted to a reasonable height, tighten the fastening screws.
6, rubber wheel speed can be adjusted, the speed will be adjusted to the speed range within the processing line.
7, before production, must check the processing parts tolerance: A: thickness B: width.
The impurity particles is not allowed to enter orbit, 8.
9, grinding did not use special grinding fluid cooling, after the completion of processing, please scrub machine tools, and timely good rust proof oil, avoid rust and other faults.
10. The machine bed track and other lubrication parts are lubricated by ordinary machine oil.
11, after a period of time, such as found in conveyor belt weak, non elastic, you need to replace the new band.
Five, electrical principle diagram (attached)
Connect the wiring with 380 volt three-phase wire, and connect the reliable ground wire. Power line should take the knife switch, please try to connect the wire after the motor start button, pay attention to the direction of rotation of the grinding wheel spindle. The spiral fuse and overload protector are used in the control line of the electric appliance.
Six 、 installation and adjustment of machine tools
After positioning the machine tools, adjust the foot of the machine and adjust it according to the level. Then put away the cooler and connect to the power supply.
Seven, the machine size: 2000mm x 1200mm * 1450mm
Eight, the machine weight: 1800kg or so