BSO-A horizontal automatic angle grinder manual
BSO-A horizontal automatic angle grinder is a special equipment for grinding the chamfering of NdFeB magnetic material.
I. main parameters of machine tools:
1, diameter size processing range (mm): Phi 8mm ~ Phi 18 mm
2, the thickness of the processing range (mm): 1.5mm ~ 25mm
3, processing line speed (cm/min): 200 cm/min to 250 cm/min
4, grinding angle width range: 0.2mm to 0.8mm
5, the conduction band up and down stroke (mm): 60 mm
6. Main motor (AC380V * 50Hz) 0.75KW * 1460r/min * 2; vice motor (AC380V * 50Hz) 1.1KW * 1460r/min; oil pump (AC380V * 50Hz) 0.12KW * 1460r/min
Two. Name of each part of machine tool
1, the parts of the machine tool is composed of a box body, column, adjustable foot etc..
2. The grinding head parts are made up of grinding head frame, spindle, diamond grinding wheel and bearing motor, motor adjusting plate and so on.
3. The carriage parts are composed of the carriage, the flat plate, the stopper, the platen, the screw rod, the handwheel and so on. 4, adjustable feeding part is composed of motor, reducer, gear FM, drive rod, synchronous belt wheel and a tensioning device of ball screw and handwheel.
5. Automatic feeding system consists of vibrator, adjustable track and so on.
6. Cooling system.
7 、 electrical appliance frequency modulation speed regulating system.
Three. Operation procedure of machine tools
1, before starting, first check the direction of the wheel rotation, according to the arrow direction is correct.
2, before and after the grinding head is strictly prohibited at the same time start, you need to open a grinding head, until the rotation is smooth, then start another grinding head.
3. The work carries the conduction band, the transportation direction is the backward rotation, its speed adjustment device is the frequency conversion motor controller, moves the frequency conversion knob, speeds up the work to need.
4, the feeding vibrator is used, put the workpiece into tray and the vibrator discharging track center alignment switchboard on the track of the center, then turn on the power switch, the switch knob to adjust pressure to just make the products smooth vibration energy into orbit. Switch the voltage regulator to 0 position at shutdown, then turn off the power supply.
5, when processing products first adjust the wheel side of the track, so that the grinding side of the track to the distance between the grinding wheel surface meets the product processing requirements (i.e. product processing chamfer amount decided), and then move the other side rail, the distance between the two track just processing products passed, finally to conveyor belt as the center, regulation two the wheel frame retreat, the track center to form a straight line.
6, according to the size of the diameter of processing products to adjust the conduction band height between the conduction band and the pressure of the product so that the products can smooth rolling, proper height after the conveying screw cylindrical guide rod on the fixing band.
Tolerance A must first check the products before feeding, 7: diameter B: thickness tolerance if there is poor product mix, it may produce the workpiece card in orbit can not move forward, you should immediately stop the wheel running, increase transport out unqualified conduction band.
The impurity particles is not allowed to enter 8, vibrator and track.
9, grinding with saponification solution, adding water for cooling. When the work is finished, please scrub the machine tools, and put on good antirust oil, avoid rust and other faults.
10. The machine bed track and other lubrication parts are lubricated by ordinary machine oil.
11, after a period of time, such as the conveyor belt and the five elastic found weak, you need to replace the new band.
Four, electrical principle diagram (attached)
Connect the wiring with 220 volt three-phase wire, and connect the reliable ground wire. Power line should take the knife switch, please try to connect the wire after the motor start button, pay attention to the direction of rotation of the grinding wheel spindle. The spiral fuse and overload protector are used in the control line of the electric appliance.
Five 、 installation and adjustment of machine tools
After positioning the machine tools, adjust the foot of the machine and adjust it according to the level. Then put away the cooler and connect to the power supply.
Six, the machine size: 1300mm x 1200mm * 1450mm
Seven, this machine weight: 1000 kg.